STAFIX®GRIP UV–INKJET film is printable with UV and UV LED curable inks only. The film does not have a receptive primer and therefore it cannot be printed with solvent or water based inks.
STAFIX®GRIP is a glue-free sticker material that adheres to various clean and very smooth surfaces with a silicon adhesion layer.
The material is removable without leaving any residue and reusable even up to 12 months. The material adheres on the unprinted side only.
STAFIX®GRIP UV-INKJET is available in white and clear and comes in rolls.
The STAFIX®GRIP UV–INKJET film is printable with UV and UV LED curable inks only. The film does not have a receptive primer and therefore it cannot be printed with solvent or water based inks.
In the sealed original package, unprinted material can be stored:
STAFIX®GRIP UV-INKJET White Polypropylene 18 months
STAFIX®GRIP UV-INKJET Clear PET 24 months
|PACKAGING & FORMATS|
|1370mm x 30m
• Pallets of 40 rolls (40 boxes)
|1370mm x 100m
• Pallets of 20 rolls (20 boxes)
|610mm x 5m
• Test roll
|Finishing||Matte||Glossy / Clear|
|ROLL LENGTH||30 m||100 m||30 m||100 m|
|Roll Diameter (OD)||mm||126||189||118||169|
|Core||mm||76,2 (3″)||76,2 (3″)||76,2 (3″)||76,2 (3″)|
Rolls: 0,5% in length, 0,1% in width
Store the unwrapped STAFIX®GRIP in the original package at 25% to 50% relative humidity and 15°C to 25°C temperature. The material should remain sealed in the original wrap until the STAFIX®GRIP material has warmed up to print-room temperature.
Print-room recommended relative humidity is 50% to 60% and temperature is 18°C to 30°C. After use re-seal the remaining unused material in the original package. Proper acclimatization allows for better feeding through the press.
|STORAGE CONDITIONS||PRINTING CONDITIONS|
|Humidity||25% to 50%||40% to 60%|
|Temperature||15° to 25 °C||18º to 30º|
|FORMAT||TEMPERATURE DIFFERENCE (°C)|
|UV-INKJET rollen, 1370mm x 30m (white)||One box (1 roll)||9 KG||2||2||2||2||3||3||3||4|
|UV-INKJET Rolls, 1370mm x 30m (transparent)||One box (1 roll)||12 KG||2||2||2||2||3||3||3||4|
|UV-INKJET Rolls, 1370mm x 100m (white)||One box (1 roll)||25 KG||3||3||3||3||4||4||4||5|
|UV-INKJET Rolls, 1370mm x 100m (transparent)||One box (1 roll)||34 KG||3||3||3||3||5||5||5||6|
When printing an artwork on the clear material that will be used for window advertising, print the image mirror-wise and apply an additional covering white layer (either printed or a laminated layer) to reduce the transparency.
The sticker or poster is always installed from the unprinted side to the glass. The material adheres only from the unprinted side.
The STAFIX®GRIP UV–INKJET film is printable with UV and UV LED curable inks only. The film does not have a receptive primer and therefore it cannot be printed with solvent or water based inks. Adjust the UV lamps to a minimum level that still cures the inks but does not deform the film.
If you have problems with the registration of the clear film it is recommended to apply masking tape along the edge of the material to allow for the sensors to gain registration of the clear material.
STAFIX®GRIP UV-INKJET materials can be cut on the press’s own cutting system or on a table cutter. The white (PP) material is softer than the clear (PET) material and may need different pressure to be cut.
STAFIX®GRIP can be die-cut and kiss-cut. Always round the corners when die-cutting or kiss cutting because the inner-sharp corners might cause the film to tear Perforating, binding and direct mail inserting is also possible. When trimming, use sharp, nick-free blades.
PACKING & SHIPPING
Protect the products well from dust when sending the finished goods to your client. Do not fold the material.